EUTECH INSTRUMENTS CYBERSCAN DO 5000 DO METER Manual de instrucciones Pagina 42
- Pagina / 76
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Instruction Manual PD 300
8.6 P1.0 (dPr): Dissolved Oxygen Parameters
This sub group is available in % saturation and mg/L (ppm) mode and lets you adjust the
barometric pressure and salinity (% saturation mode only).
8.6.1 P1.1 Pressure adjustment mode
Barometric pressure is vital to correct dissolved oxygen measurements. You need to enter the
correct barometric pressure of the area you are measuring. This mode lets you perform two
functions:
• Select either mm Hg or Pascal barometric pressure units.
• Adjust the barometric pressure. See Addendum 2 on page 67 for a
“Pressure vs Altitude” table.
From measurement mode:
1. Press the MODE key to select DO measurement mode.
2. Press the SETUP key to enter SETUP mode.
3. Press the ▲ or ▼ keys to scroll through su/jointfilesconvert/267593/bgroups until you view parameter “dPr” in the
upper display.
4. Press the ENTER key twice. The upper display shows either Hg or PA and the lower
display shows bAr. See figure on next page.
5. Press the ▲ or ▼ keys to toggle between mm Hg and Pascal units.
6. Press the ENTER key to confirm selection and move to the next screen. The upper
display shows the barometric pressure and the lower display shows the units selected in
Step 3.
7. Press the ▲ or ▼ keys to adjust the barometric pressure. The pressure adjustment
range is 500 to 1499 mm Hg (66.6 to 199.9 kPa).
8. Press the ENTER key to confirm selection and move to Step 4 on page 39 [salinity
adjustment appears in mg/L (ppm) measurement mode only]. If instead you want to
return to measurement mode, press CAL/MEAS twice.
37
- Instruction Manual 1
- Preface 3
- TABLE OF CONTENTS 4
- WARRANTY 69 5
- RETURN OF ITEMS 70 5
- 1 INTRODUCTION 6
- 2.1 Display 7
- 2.2 Keypad 8
- 3 PREPARATION 9
- 3.2 Probe Information 10
- Instruction Manual PD 300 11
- 4 CALIBRATION 12
- 4.2 Temperature Calibration 13
- 4.3 pH calibration 14
- Figure 6: pH Calibration 15
- Figure 9: DO Probe guard 17
- 100% saturation 18
- Figure 10: To calibrate for 18
- Figure 11: To calibrate for 19
- 0% saturation 19
- 5 MEASUREMENT 22
- Taking Measurements (pH) 24
- 5.2 Taking DO readings 26
- Figure 18 – Auto endpoint 27
- 6 HOLD FUNCTION 29
- 7 BACKLIT LCD 30
- 8 ADVANCED SETUP FUNCTIONS 31
- SETUP in pH Measurement Mode 32
- % Saturation Measurement Mode 33
- • P2.2 = Electrode slope 36
- Figure 24 – P 3.1: Selecting 38
- READY function) 38
- Figure 26 – P3.3: Select 40
- Measurement 45
- Figure 33: iew electrode 47
- Figure 34: View electrode 48
- (ppm) mode 48
- Figure 37: To configure for 50
- READY and Auto Endpoint 50
- Figure 40: Adjusting LCD 53
- Figure 41: Reset to factory 54
- 9.1 pH Electrode care 55
- After measuring 55
- 9.6 Electrolyte Solution 62
- 10 TROUBLE SHOOTING GUIDE 65
- 11 ERROR MESSAGES 66
- 12 SPECIFICATIONS 67
- 13 ACCESSORIES 68
- Oakton Instruments 69
- Calibration Solutions 70
- 17 WARRANTY 74
- 18 RETURN OF ITEMS 75
Relacionado con productos y manuales para De medición, control y control EUTECH INSTRUMENTS CYBERSCAN DO 5000 DO METER
De medición, control y control EUTECH INSTRUMENTS ALPHA PH 500 PHORP 2-WIRE TRANSMITTER Guía de usuario
(36 paginas)
(36 paginas)
De medición, control y control EUTECH INSTRUMENTS ALPHA COND 500 - REV 4 Manual de instalación
(20 paginas)
(20 paginas)
De medición, control y control EUTECH INSTRUMENTS CYBERSCAN DO 1500 DO METER Manual de instrucciones
(60 paginas)
(60 paginas)
De medición, control y control EUTECH INSTRUMENTS CYBERSCAN PC 10 COMBINATION PHCONDUCTIVITY METER Manual de usuario
(20 paginas)
(20 paginas)
De medición, control y control EUTECH INSTRUMENTS CON 700 - REV 2 Manual de instrucciones
(24 paginas)
(24 paginas)
De medición, control y control EUTECH INSTRUMENTS ION 700 - REV 3 Manual de instrucciones
(24 paginas)
(24 paginas)
De medición, control y control EUTECH INSTRUMENTS CYBERSCAN DO 1500 DO METER Manual de usuario
(10 paginas)
(10 paginas)
De medición, control y control EUTECH INSTRUMENTS ION 700 - REV 3 Manual de instrucciones
(36 paginas)
(36 paginas)
De medición, control y control EUTECH INSTRUMENTS CYBERSCAN PH500 PHORP BENCH METER Manual de usuario
(12 paginas)
(12 paginas)
De medición, control y control EUTECH INSTRUMENTS ALPHA COND 200 - REV 3 Manual de instrucciones
(40 paginas)
(40 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.069 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales