EUTECH INSTRUMENTS PH 6 PLUS PH MV TEMP Manual de instrucciones Pagina 40
- Pagina / 64
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Instruction Manual CyberScan pH 1100/ 2100
40
10.3.4 Stability setup program P2.2
Use this program to turn on or off the mV stability indicator and
to set level of stability (low, medium or high).
Stability definitions
High stability:
reading is stabilized quickly, but reading is less accurate.
Medium stability:
reading stability is averaged between high and low stability.
Low stability:
reading is stabilized slowly, but guarantees high accuracy
1. Enter mV setup mode as described in steps 1-4 in Section
10.3.1 Entering mV setup mode (page 37).
2. Use ∆/MI key to scroll to program Stability Setup: P2.2. See
Figure 119.
3. Press ENTER to enter program Stability Setup: P2.2.
4. Press >/CAL to toggle between mV Stable Criteria: On and
Off. The selection will flash. See Figure 120.
5. Press ENTER to confirm selection.
• If you selected On, continue to step 6.
• If you select Off, pressing ENTER returns to the setup
mode.
Press ∆/MI key to continue to the next setup program, or
press ∇/MR to go to the previous program. Press EXIT to
return to the mV measurement mode.
6. If you selected On in step 5, the display now reads Degree of
Stability: Low Medium High. Press >/CAL to toggle between
Low, Medium and High. The selection will flash.
See Figure 121.
7. Press ENTER to confirm selection and return to the setup
mode. Press ∆/MI to continue to the next setup program, or
press ∇/MR to go to the previous program. Press EXIT to
return to the pH measurement mode.
Degree of Stability
Low Medium High
mV Stable Criteria
On Off
Stability Setup : P2.2
Press ENT. to Select
Figure 119
Figure 120
Figure 121
- Instruction Manual 1
- PREFACE 3
- TABLE OF CONTENTS 4
- 1 INTRODUCTION 6
- Figure 1: Membrane Keypad 7
- 1.3 Rear Panel 8
- 1.4 Electrode Holder 9
- 2 STARTING UP 10
- Attention: 10
- Selectable buffer sets: 11
- Figure 13 12
- Figure 14 12
- Figure 15 12
- . See Figure 17. This 13
- Cal Done 13
- NOTE: 14
- . See Figure 26. Press 15
- 3.2 pH measurement 16
- Figure 35 17
- Figure 36 17
- 18
- pH/Temp mV Ion 19
- 5.1 Ion calibration 20
- Ion Conc: 1.0ppm 21
- 3 Point Cal Done 21
- Aver. Slope = 49.2mV 21
- Sys Updating. . 21
- 5.3 Ion measurement 22
- 5.695pH 25.3 C ATC 23
- Data Log. . . . Loc: 9 23
- 6.2 Memory recall 24
- 7.546pH 25.4 C ATC 25
- 9.1 Temperature Calibration 26
- 10.1 Setup mode overview 27
- Tx/Rx Parameter: P4.4 29
- Press ENT. to Select 29
- USA NST Bf1 Bf2 Cust 30
- Select & Press ENTER 30
- Figure 83 31
- Figure 84 31
- Figure 85 31
- Figure 86 31
- Key In Low Alarm 32
- Key In High Alarm 32
- Figure 91 33
- Figure 92 33
- Figure 93 33
- Figure 94 34
- Figure 95 34
- Figure 96 34
- Figure 101 35
- = 0.2 mV 35
- Figure 105 36
- Figure 106 36
- Figure 107 36
- Figure 108 36
- Figure 109 37
- Figure 110 37
- Figure 111 37
- Figure 112 38
- Figure 113 38
- Figure 1 38
- Figure 115 38
- Figure 116 39
- Figure 117 39
- Figure 118 39
- Figure 119 40
- Figure 120 40
- Figure 121 40
- Figure 124 41
- = 3.2 mV 41
- Figure 125 42
- Figure 126 42
- Figure 127 42
- Figure 128 42
- Figure 132 43
- Figure 133 43
- Figure 134 44
- Figure 135 44
- Figure 136 44
- Figure 137 44
- Figure 138 45
- Figure 139 45
- Figure 140 45
- Figure 141 46
- Figure 142 46
- Figure 143 46
- Resolution: High Low 47
- Ion Mode Setup : P3.4 47
- Figure 155 49
- Figure 156 49
- Figure 157 49
- Figure 158 49
- Figure 167 51
- Figure 168 51
- Figure 169 51
- Memory Recall Mode 52
- Auto Manual 52
- MemRecall Setup:P4.3 52
- Data send to printer 53
- Current Memory 53
- Data Transfer :P4.5 53
- Figure 185 54
- Figure 186 54
- Figure 187 54
- Figure 184 54
- 11 ELECTRODE CARE 55
- 12 RS 232 COMMUNICATION 56
- 13 ADDITIONAL INFORMATION 57
- Offset of temp. probe 59
- Temperature 60
- 17 ACCESSORIES 61
- 18 WARRANTY 62
Relacionado con productos y manuales para De medición, control y control EUTECH INSTRUMENTS PH 6 PLUS PH MV TEMP
De medición, control y control EUTECH INSTRUMENTS ALPHA PH1000 PHORP CONTROLLERTRANSMITTER Manual de instrucciones
(40 paginas)
(40 paginas)
(4 paginas)
De medición, control y control EUTECH INSTRUMENTS ALPHA COND 560 Manual de instrucciones
(52 paginas)
(52 paginas)
De medición, control y control EUTECH INSTRUMENTS ALPHA PH1000 PHORP CONTROLLERTRANSMITTER Manual de usuario
(20 paginas)
(20 paginas)
De medición, control y control EUTECH INSTRUMENTS ALPHA CON 500 2-WIRE TRANSMITTER Instrucciones de operaciones
(34 paginas)
(34 paginas)
De medición, control y control EUTECH INSTRUMENTS ECOSCAN TEMP JKT PORTABLE METER Manual de instrucciones
(20 paginas)
(20 paginas)
De medición, control y control EUTECH INSTRUMENTS ECOSCAN TEMP 456 TEMPERATURE METER Manual de instrucciones
(24 paginas)
(24 paginas)
De medición, control y control EUTECH INSTRUMENTS ALPHA PH1000 PHORP CONTROLLERTRANSMITTER Manual de instrucciones
(42 paginas)
(42 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.043 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales