EUTECH INSTRUMENTS ALPHA COND 500 - REV 4 Especificaciones descargar pdf (Pagina 32)

Transmitter Cond/Res 2-Channel M300 32

Printed in Switzerland 52 121 318

If Auto-range was selected then Aout max1 can be conﬁgured. Aout max1 is the maximum

value for the ﬁrst range on Auto-Range. The maximum value for the second range on Auto-

Range was set in the previous menu. If Logarithmic Range was selected, it will also prompt for

the number of decades as ‘Aout1 # of Decades =2’.

The value for the Hold mode can be conﬁgured to hold the last value or can be set to a Fixed

value.

Pressing the [ENTER] key again will bring up the Save Changes dialog. Selecting No will dis-

card the entered values and return to the measurement display screen, selecting Yes will save

changes made.

1 2 ... 27 28 29 30 31 32 33 34 35 36 37 ... 63 64

Operation Manual 1
Conductivity/Resisitivity 1
2-Channel 1
Transmitter M300 1
1 Introduction 7
2 Safety instructions 7
3 Unit overview 9
3.3 Control/Navigation Keys 11
3.3.6 “Save changes” dialog 13
3.3.7 Security Passwords 13
3.4 Display 13
4 Installation instruction 14
2 Terminal for sensor 19
4.3 Connector PIN deﬁnition 20
6 Quick Setup 21
6.3 Measurement Units 22
6.4 Analog Outputs 22
6.5 Setpoint 23
7 Sensor Calibration 24
7.5 Sensor Veriﬁcation 27
8 Conﬁguration 28
8.2.1 Channel Setup 29
8.2.2 Temperature Source 29
8.2.4 Set Averaging 31
8.3 Analog Outputs 31
8.4 Setpoints 33
8.5 Alarm/Clean 36
8.5.1 Alarm 36
8.5.2 Clean 37
8.6 Display 37
8.6.1 Measurement 37
8.6.2 Resolution 38
8.6.3 Backlight 38
8.6.4 Name 38
8.7 Hold Analog Outputs 39
9 System 40
9.3 Passwords 41
9.3.1 Changing Passwords 41
9.4 Set/Clear Lockout 41
9.5 Reset 42
9.5.1 Reset System 42
10 PID Setup 43
10.1 Enter PID Setup 44
10.2 PID Auto/Manual 44
10.3 Mode 45
10.3.1 PID Mode 45
10.4 Tune Parameters 45
10.4.3 Proportional Limits 46
10.4.4 Corner Points 46
10.5 PID Operation 46
11 Service 47
11.1.2 Digital Input 48
11.1.3 Display 48
11.1.4 Keypad 48
11.1.5 Memory 49
11.1.6 Set Relay 49
11.1.7 Read Relays 49
11.1.8 Set Analog Outputs 50
11.1.9 Read Analog Outputs 50
11.2 Calibrate 51
11.2.1 Calibrate Meter 51
11.2.2 Calibrate Analog 53
11.2.3 Calibrate Unlock 54
11.3 Tech Service 54
12 Info 55
12.2 Calibration Data 56
12.3 Model/Software Revision 56
13 Maintenance 57
14 Troubleshooting 57
14.1 Changing the Fuse 58
16 Speciﬁcations 59
17 Default tables 61
18 Waranty 62
19 UL Statement (Pending) 62
Addresses 64

Comentarios a estos manuales

Sin comentarios

EUTECH INSTRUMENTS ALPHA COND 500 - REV 4 Especificaciones Pagina 32

Comentarios a estos manuales

Relacionado con productos y manuales para De medición, control y control EUTECH INSTRUMENTS ALPHA COND 500 - REV 4